Tc-electronic P2 Manuel d'utilisateur télécharger pdf (Page 19)

34 35

APPENDIX TROUBLESHOOTING

Loading Preset Banks

The P2 is loaded with the 8 presets from the

Default F1 bank (see page 37). These are the

presets accessible from the Front Panel .

However, it is possible to load other banks into

the front panel. To do this:

• Press and hold LOCK when powering up.

All key LEDs will flash.

• Press the key equivalent to the bank you

wish to load to the front panel.

• Now the LEDs in the LOCK and BYPASS

keys will flash.

• Press LOCK (green LED) to proceed/confirm

loading the selected bank or press BYPASS

(red LED) to decline/exit the bank load mode.

Notes

Reboot the TC Icon PC Editor between

connecting different P2 units.

Port Conflict

Another active application may conflict with

the serial ports you have selected on the:

Setup - Devices - Ports page.

If this is the case the following screen will

appear.

There are two options to resolve this

problem:

1 Connect the P2 to another physical COM

port and select this COMport an the COM

port page.

2 Close the conflicting application.

APPENDIX - TECHNICAL SPECIFICATIONS

Digital Inputs and Outputs

Connectors:

Formats:

Output Dither:

Word Clock Input:

Sample Rates:

Processing Delay:

Additional Delay:

Frequency Response DIO:

Sample Rate Conversion

Type:

Dynamic Range:

THD+N:

Input Rate Range:

Analog Inputs

Connectors:

Impedance:

Max. Input Level:

Min Input Level (for 0 dBFS):

A to D Conversion:

A to D Delay:

Dynamic Range:

THD:

Frequency Response:

Crosstalk:

Analog Outputs

Connectors:

By-pass:

Impedance:

Max. Output Level:

Full Scale Output Range:

D to A Conversion:

D to A Delay:

Dynamic Range:

THD:

Frequency Response:

Crosstalk:

EMC

Complies with:

Safety

Certified to:

Environment

Operating Temperature:

Storage Temperature:

Humidity:

PCMCIA Interface

Connector:

Standards:

Card Format:

Control Interface

RS232

GPI, Pedal, Fader:

General

Finish:

LCD:

Dimensions:

Weight:

Mains Voltage:

Power Consumption:

Backup Battery Life:

Warranty

Parts and labor:

XLR (AES/EBU), RCA Phono (S/PDIF)

AES/EBU (24 bit), S/PDIF (24 bit), EIAJ CP-340, IEC 958

HPF TPDF dither 8-22 bit

BNC, 75 ohm, 0.6 to 10 Vpp

32 kHz, 44.1 kHz, 48 kHz

0.5 ms @ 48 kHz

0-1000 ms at all sample rates

DC to 23.9 kHz ± 0.01 dB @ 48 kHz

Asynchronous

120 dB

-106 dB 44.1 to 48 kHz @ 1 kHz, -2 dBFS

31 kHz to 49 kHz

XLR balanced (pin 2 hot)

20 kohm (balanced)

+28 dBu (balanced)

-4 dBu (balanced)

24 bit (1 bit, 128 times oversampling)

0.8 ms @ 48 kHz

>103 dB (unweighted), >106 dB(A)

-95 dB (0.0018 %) @ 1 kHz, -6 dBFS (FS @ +18 dBu)

10 Hz to 20 kHz: +0/-0.2 dB

<-80 dB, 10 Hz to 20 kHz, typical –100 dB @ 1 kHz

XLR balanced (pin 2 hot)

Through relay

40 ohm (balanced)

+26 dBu (balanced)

-4 dBu to +26 dBu (balanced)

24 bit (1 bit, 128 times oversampling)

0.57 ms @ 48 kHz

>100 dB (unweighted), >104 dB(A)

-86 dB (0.005 %) @ 1 kHz, -6 dBFS (FS @ +18 dBu)

10 Hz to 20 kHz: +0/-0.5 dB

<-60 dB, 10 Hz to 20 kHz, typical –90 dB @ 1 kHz

EN 55103-1 and EN 55103-2

FCC part 15, Class B

CISPR 22, Class B

IEC 60065, EN 60065, UL 6500 and CSA E65

CSA FILE #LR108093

32° F to 122° F (0° C to 50° C)

-22° F to 167° F (-30° C to 70° C)

Max. 90% non-condensing

PC Card, 68 pin type 1 cards

PCMCIA 2.0, JEIDA 4.0

Supports up to 2 MB SRAM

9 Pin SUB-D

1/4 inch phone jack

Anodized aluminum face and top plate

Plated and painted steel chassis

56 x 128 dot graphic LCD-display

19" x 1.75" x 8.2" (483 x 44 x 208 mm)

5.2 lb. (2.35 kg)

100 to 240 VAC, 50 to 60 Hz - (auto-select)

<20 W

>10 years

1 year

Due to continuous development

these specifications are subject

to change without notice.

1 2 ... 14 15 16 17 18 19 20 21

Commentaires sur ces manuels

Pas de commentaire

Tc-electronic P2 Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires audio Tc-electronic P2